IEC 60115-1 pdf download

IEC 60115-1 pdf download Fixed resistors for use in electronic equipment – Part 1: Generic specification
1General
1.1scope
This part of lEC 60115 is applicable to fixed resistors for use in electronic equipment.
lt establishes standard terms, inspection procedures and methods of test for use in sectionaland detail specifications of electronic components for quality assessment or any other purpose.
1.2Normative references
The following normative documents contain provisions which，through reference in this text,constitute provisions of this part of lEC 60115.For dated references,subsequent amendmentsto,or revisions of any of these publications do not apply. However，parties to agreementsbased on this part of iEC 60115 are encouraged to investigate the possibility of applying themost recent editions of the normative documents indicated below.For undated references, thelatest edition of the normative document referred to applies.Members of lEC and Iso maintainregisters of currently valid lnternational Standards.
NOTE In the case of lEC 60068 standards,use the referenced edition.
IEC 60027(all parts),Letter symbols to be used in electrical technologyIEC 60050(all parts),International Electrotechnical Vocabulary (IEV)
lEC 60060-1:1989，High-voltage test techniques – Part 1: General definitions and testrequirements
IEC 60060-2:1994,High-voltage test techniques – Part 2: Measuring systems
IEC 60062:1992,Marking codes for resistors and capacitors
Amendment 1 (1995)
lEC 60063:1963,Preferred number series for resistors and capacitorsAmendment 1 (1967)
Amendment 2 (1977)
IEC 60068-1:1988,Environmental testing – Part 1: General and guidanceAmendment 1 (1992)
IEC 60068-2-1:1990: Environmental testing – Part 2: Tests – Tests A: ColdAmendment 1 (1993)
Amendment 2 (1994)
IEC 60068-2-2:1974,Environmental testing – Part 2: Tests – Tests B: Dry heatAmendment 1 (1993)
Amendment 2 (1994)
IEC 60068-2-3:1969,Environmental testing – Part 2: Tests -Test Ca: Damp heat, steady stateAmendment 1 (1984)
IEC 60068-2-13:1983，Environmental testing – Part 2:Tests – Test M: Low air pressure
IEC 60068-2-14:1984,Environmental testing – Part 2:Tests -Test N: Change of temperatureAmendment 1 (1986)
IEC 60068-2-20:1979,Environmental testing – Part 2: Tests – Test T: SolderingAmendment 2 (1987)
IEC 60068-2-21:1983，Environmental testing — Part 2:Tests -Test U: Robustness of termina-tions and integral mounting devices
Amendment 2 (1991)
Amendment 3 (1992)
IEC 60068-2-27:1987,Environmental testing — Part 2:Tests – Test Ea and guidance: ShocklEC 60068-2-29:1987,Environmental testing — Part 2:Tests – Test Eb and guidance: Bump
IEC 60068-2-30:1980，Environmental testing – Part 2: Tests – Test Db and guidance: Dampheat,cyclic (12 +12 hour cycle)
Amendment 1 (1985)
IEC 60068-2-45:1980，Environmental testing – Part 2:Tests – Test XA and guidance: lmmer-sion in cleaning solvents
Amendment 1 (1993)
IEC 60068-2-58:1989,Environmental testing – Part 2:Tests -Test Td: Solderability, resistanceto dissolution of metallization and to soldering heat of Surface Mounting Devices(SMD)
IEC 60195:1965,Method of measurement of current noise generated in fixed resistors
IEC 60249-2-4:1987,Base materials for printed circuits – Part 2: Specifications – Speci-fication No.4:Epoxide woven glass fabric copper-clad laminated sheet, general purpose grade
IEC 60294:1969，Measurement of the dimensions of a cylindrical component having two axialterminations
IEC60410:1973,Sampling plans and procedures for inspection by attributesIEC 60440:1973,Method of measurement of non-linearity in resistors
IEC QC 001002-3:1998,IEC Quality Assessment System for Electronic Components (IECQ) -Rules of procedure – Part 3: Approval procedures
IEc Qc 001003:1998,IEC Quality Assessment System for Electronic Components (IECQ) -Guidance documents